Push and hold TSC for over 1 second.

New! For the newest BMW motorcycles with CAN-BUS technology. Now use the turn signal cancel button (TSC) on your R and K series 2005 to 2008.

Already proven performance for R and K series bikes. See R1200GS install and K1200GT install pictures. New F series bikes to be updated soon.

Now featuring always ON red LED to tell you the aux lights are OFF. LED goes green when your aux lights are ON.

For BMW R & K series 1990s-2005 (Non CAN-BUS).

For BMW motorcycles R and K series with the electronic turn-signal-cancel (TSC) on the right switch cluster, early 1990s and until the end of all (Oilhead R-259) R1150, R1200C, R1200CL and K1200RS and GT to 2005. For K1200LT until 2008.

Special version activates your hidden garage door remote. Takes 2 quick pulses of the TSC. Closes a tiny onboard relay contact for 2 seconds. This then simulates the pushbutton on your garage door remote control. Requires opening up your remote to solder in 2 wires at right location. OR we modify your remote for $23 post paid.

For any car or motorcycle.

For all motorcycles (& Cars/SUVs etc) because it senses the power going to the high beam bulb/headlight. Autoswitch detects the high beam wire only inside the 1.2 second to 10 seconds span. It will work with any other +12VDC timed source on the car or bike as well.

The visual LED blinks rapidly during the timed "window" up to 10 seconds long when you should release the trigger signal (high beam switch). The single tap to flash the high beams or leaving the high beams on will not activate the Autoswitch. LED shines green to indicate power to your auxiliary lights relay.

For any car or motorcycle.

For all motorcycles (& Cars/SUVs etc) because it senses the power going to the high beam bulb/headlight. Autoswitch detects the high beam wire only if it detects 2 quick taps inside a 1.2 second time span. It will work with any other +12VDC timed source on the car or bike as well.

The visual LED blinks rapidly during the timed "window" during which the 2 taps must be completed by the trigger wire.(high beam switch). The single tap to flash the high beams or leaving the high beams on will not activate the Autoswitch. LED shines green to indicate power to your auxiliary lights relay.

For any car or motorcycle.

Available again December 2007! Special version activates your hidden garage door remote. Takes 2 quick pulses of the TSC. Closes a tiny onboard relay contact for 2 seconds. This then simulates the pushbutton on your garage door remote control. Requires opening up your remote to solder in 2 wires at right location. OR we modify your remote for $23 post paid.

For all motorcycles (& Cars/SUVs etc) because it senses the power going to the high beam bulb/headlight. Autoswitch detects the high beam wire only if it detects 2 quick taps inside a 1.2 second time span. It will work with any other +12VDC timed source on the car or bike as well.

For BMW R & K series 1990s-2005 (Non CAN-BUS)

For BMW motorcycles R and K series with the electronic turn-signal-cancel (TSC) on the right switch cluster, early 1990s and until the end of all (Oilhead R-259) R1150, R1200C, R1200CL and K1200RS and GT to 2005. For K1200LT until 2008.

AutoSwitch model 5NB2 works by sensing the chassis-ground connection from the TSC when the button is pressed twice quickly. The visual LED blinks rapidly during the timed "window" up to 1.2 seconds long during which the 2 taps must be completed. The single tap on the TSC button to cancel the turn signal will not activate the Autoswitch. LED shines green to indicate power to your auxiliary lights relay.